# How does Traffic Lab use studies to calibrate its simulator?

Traffic Lab calibrated its main highway entrance against **one German design capacity for four continuous lanes**. Simulated hourly counts at other desired speeds and a field comparison at a work zone show how the setting behaves in other cases.[^1]

[HTML version](https://onemorelane.org/en/faq/studies-and-traffic-simulation-calibration/)

![Overhead view of cars and a truck on parallel motorway lanes.](https://onemorelane.org/photos/lanes-960.webp)

Illustrative photo · [Bernd Dittrich / Unsplash](https://unsplash.com/photos/W0A8qmTS8IU)

## What was calibrated?

At the main entrance, vehicles wait for a gap large enough to enter while moving. The calibration set the net time gap in this entry rule to **1.7 seconds**. The reference scenario had four continuous lanes, no ramp and a desired speed of 100 km/h.[^1]

The German highway capacity manual (HBS) gives the design values used to calculate the benchmark. The value of 7,120 vehicles per hour is interpolated between the 10% and 20% heavy-vehicle columns for a 12% share. The model median of 7,196 vehicles per hour was about **1.1% higher than the benchmark**.[^1][^2]

## What did the other scenarios check?

After calibration, the team tested the reference road at desired speeds of 80 and 120 km/h. A field study at a work zone in North Rhine-Westphalia provided a benchmark for the lane drop. The work zone had a different gradient, vehicle mix and measurement method. The calibration result and the follow-up comparisons describe those specific conditions.[^1][^3]

Model medians from three hour-long runs per scenario compared with design and field values · vehicles per hour per direction[^1]

| Scenario | Benchmark | Model |
| --- | ---: | ---: |
| 4 → 4 · 100 km/h · calibration | 7,120[^2] | 7,196 |
| 4 → 4 · 80 km/h | 7,120[^2] | 6,946 |
| 4 → 4 · 120 km/h | 7,120[^2] | 7,352 |
| 2 → 1 · 80 km/h · work zone | 1,739[^3] | 1,827 |

## What a calibration figure tells you

A fitted value only shows that the model matches that one case. Whether it also holds at another speed or a narrower cross-section takes an independent measurement.

## Test it in the simulator

Open the reference road with four continuous lanes at a desired speed of 100 km/h.

- [Open the calibration run](https://onemorelane.org/en/highway/?map=highway&preset=custom&seed=1187&lanes=4&exitLanes=4&speed=100&attention=80&demand=160&style=balanced&extended=0)

## Related questions

- [Why can the busiest minute overstate hourly traffic flow?](https://onemorelane.org/en/faq/why-a-peak-minute-overstates-hourly-traffic-flow/index.md)
- [How do three-to-two and two-to-one lane drops compare?](https://onemorelane.org/en/faq/three-to-two-vs-two-to-one-lanes/index.md)
- [How many vehicles can pass a one-lane highway work zone at 80 km/h?](https://onemorelane.org/en/faq/one-lane-highway-work-zone-80-kmh/index.md)

## Sources

[^1]: [Traffic Lab · Main entrance calibration and hourly measurements (German)](https://github.com/mb4umi/onemorelane/blob/main/kapazitaetsabgleich.md#stundenmessungen-nach-der-kalibrierung)
[^2]: [Geistefeldt and Hohmann (2024) · BASt V 377, Table 2-6, p. 48 (German)](https://bast.opus.hbz-nrw.de/files/2913/V377%2BGesamtversion%2BBF.pdf)
[^3]: [Geistefeldt et al. (2024) · BASt V 378, Tables 5-1 and 5-2, pp. 75 and 80 (German)](https://bast.opus.hbz-nrw.de/files/2914/V378%20Gesamtversion%20BF.pdf)
